|
 |
|
 |
|
 |
|
|
|
 |
 |
|
|
|
|
Applications
These hard hitting Utility drills
feature high blow rate & torque, resulting in rapid drilling RCC &
masonry. Their all forged alloy steel construction proven retention
system & inbuilt lubrication circuit means excellent durability and
low operating costs.
Features
Technical Data for Utility Drill
|
|
|
|
|
|
Technical Data for Rock Drill / Jack Hammer
|
||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
Applications
The 350R drilling machine is capable
of drilling 23 mm in steel. It features a feed screw mechanism that
enable the drill to be fed into the job with accuracy and minimum
operator effort. Because of its light weight is the preferred tool for
on site drilling applications where the job is too heavy or impractical
to move.
This drill is used extensively by refineries, shipyards, offshore platforms, general engineering and fabrication shops. Model DAL 350 A-Features and Specifications
Technical Data for Pneumatic Drilling Machine
|
|
|
|
|
|
Models : EDD-15, EDD-18 Long & Short versions These rugged tools are available in five speeds and in long and short spindle versions. These widely used grinders are effective with collets and mounted, points as well as abrasive grinding wheels. Other attachments are wirebrushes and cut-off wheels. 8000 to 12000 rpm models come equipped with governors. Features 1) Forged alloy steel cylinders, Extra long life 2) 3/4 HP air motor - High Power to weight ratio. 3) Flush rotating ring type throttle. 4) A Ball bearings for extra radial support. 5) New positionable exhaust silencer. 6) Built in lubricator. Applications Dieshops : Die contouring, rework, shaping and blending. Foundries and Forge Shops : Ideally suited for casting clean-up, burr removal and smoothing of casting and forgings. Shipyards, Refineries, fabrication shops : General purpose grinding, weld grinding and smoothing, repair and reconditioning work etc. Technical Data for Die Grinders
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
Features
Technical Data for Mini Die Grinders
|
|
||||||||||||||||||||||||||||
|
|
|
|
Introduction
1) The need of a simple device to grind drill steel scientifically, maintaining all 2) Insert angles 3) Insert Radius 4) Clearance angle was long felt. The Edicon Drill Master pneumatic Grinder fulfils the above needs. How to Operate Drill 1. Position Drill Steel in vee block 2. Operate hand wheel to clamp drill steel 3. Open air control lever 4. Move swing arm along length of chisel flank 5. For diameter grinding, hook the swing by locking hook, the steel is rotated by hand against grinding wheel taking care of clearance angle 6. Use of a line lubricator is essential Advantages Any drill operator can acquire the skill to operate the Edicon Grinder for 1. Better drilling footage per hour 2. Long life of carbide insert 3. Eliminates insert failure due to incorrect hand grinding or overheating of carbide insert. Parts 1. Feed Hand Wheel 2. Springs for equalising feed 3. Coolant water pipe 4. Mechanical Drill Steel Holder 5. Lever for operating air motor 6. Hook for locking swing 7. Support for Drill Steel for diameter grinding Technical Data for Semi Automatic Drill Steel Grinders
|
|
|
|
|
Features
Technical
Data for Rammers
31/4 Rubber butts also available. Since improvements are made from time to time, specifications may change without notice |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
Features
Technical
Data for Floor Rammers
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
:: Our Product Range :: |
||||||
|
|
|
|
|
|
